data////Software//ESN200 - Software for ESN200 echosounder

Instruction for upgrade of Multi systems.pdfSome instruction for use with upgrade of Multi systems using the SKIPPER service software. <\BR> It is important that the software version in the screen and the electronic unit match. If you are replacing 1 unit , check you have the same software version, and if not update the older part.
LICENSE.lgpl-2.1.pdfSKIPPER software uses a number of Open source programs, under license type LICENSE.lgpl-2.1. This file explains and clarifies the use of the software under this license.
ESN200 1.2.0.1 - Software for ESN200 echosounder.zipContaining latest SW version for ESN200 Display (ESN200-SB) New ESN200-SC 10.1" display and Electronic unit (JB70E2) and manual, Unpack the .ZIP and use the SW-M0XXX.tar files, do not unpack these.
SW-M008-1.2.0.1 & SW-M010-1.2.0.1 & SW-M019-1.2.0.1,
Bug fix: default reduced power for transducers corrected
Important: If 1.2.0.0 has been installed before, Master reset must be used when installing later versions

based on SW-M008-1.2.0.0 & SW-M010-1.2.0.0 & SW-M019-1.2.0.0, New version with major changes:
New 10.1" display option ESN200-SC
Removal of Manual gain, and addition of Sensitivity
Addition of SDSTN message to identify Channel allowing both channels to be sent on the same NMEA output
Improvements in the transceiver and signal noise ratio
Required colour change for Invalid data.

New Approval:
IEC62288 Ed.3:2021
ISO9875:2023
New Manual
Last Updated 24.6.2025
ESN200 1.2.0.2 - Software for ESN200 echosounder.zipContaining latest SW version for ESN200 Display (ESN200-SB) New ESN200-SC 10.1" display and Electronic unit (JB70E2) and manual, Unpack the .ZIP and use the SW-M0XXX.tar files, do not unpack these.
SW-M008-1.2.0.2 & SW-M010-1.2.0.2 & SW-M019-1.2.0.2,
.2 Bug fix: Changed DEfault value of new sentences to off (DPT channel 2 and STN) for smoother upgrade
.1 Bug fix: default reduced power for transducers corrected
Important: If 1.2.0.0 has been installed before, Master reset must be used when installing later versions

based on SW-M008-1.2.0.0 & SW-M010-1.2.0.0 & SW-M019-1.2.0.0, New version with major changes:
New 10.1" display option ESN200-SC
Removal of Manual gain, and addition of Sensitivity
Addition of SDSTN message to identify Channel allowing both channels to be sent on the same NMEA output
Improvements in the transceiver and signal noise ratio
Required colour change for Invalid data.

New Approval:
IEC62288 Ed.3:2021
ISO9875:2023
New Manual
Last Updated 24.6.2025
Equivilent Software for Windows
ESN200 Windows 1.2.0.0.zipSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Latest windows software with Drivers.zipCopy this directory locally, this includes the latest software version, add other ESN200 PC version as required
The windows versions of the Multi software (Not web version) can be started using a script as follows
Start the software manually, set the LAN settings
Then use a script to start the window:
Remove the windows border : -frameless-window , the program can be killed using alt+F4
Use the saved LAN settings : -load-net-interface
Maximise the window : -maximize-window
to save the current LAN settings: -save-net-interface
Example to start automatically
start multi_screen.exe -load-net-interface -maximize-window -frameless-window
to start to select new LAN settings
Start multi_screen.exe -save-net-interface -maximize-window -frameless-window
ESN200 windows software 1.2.0.2 File only.zipSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Windows Software 1.2.0.2 with drivers.zipCopy this directory locally, this includes the latest software version, add other ESN200 PC version as required
The windows versions of the Multi software (Not web version) can be started using a script as follows
Start the software manually, set the LAN settings
Then use a script to start the window:
Remove the windows border : -frameless-window , the program can be killed using alt+F4
Use the saved LAN settings : -load-net-interface
Maximise the window : -maximize-window
to save the current LAN settings: -save-net-interface
Example to start automatically
start multi_screen.exe -load-net-interface -maximize-window -frameless-window
to start to select new LAN settings
Start multi_screen.exe -save-net-interface -maximize-window -frameless-window
Older versions
ESN200 PC Version 1 0 6.exe
The windows versions of the Multi software (Not web version) requires the ESNDrivers to be copied locally, and then this file can be copied into that directory
Select the same software version as you are running on the display
ESN200 PC Version 1 0 7.exe
ESN200 PC Version 1 0 7.zip
ESN200 Windows 1.1.2.0.exe
ESN200 Windows 1.1.2.0.zip
ESN200 Windows 1.1.3.0.exe
ESN200 Windows 1.1.3.0.zip
ESN200 Windows 1.1.4.0.exe
ESN200 Windows 1.1.4.0.zip
ESN200 Windows 1.1.4.2.exe
ESN200 Windows 1.1.4.2.zip
ESN200 Windows 1.1.4.3.exe
ESN200 Windows 1.1.4.3.zip
ESN200 Windows 1.1.4.4.exe
ESN200 Windows 1.1.4.4.zip
ESN200 Windows 1.1.4.5.exeSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Windows 1.1.4.5.zipSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Windows 1.1.5.0.exeSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Windows 1.1.5.0.zipSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
ESN200 Windows 1.2.0.0.zipSoftware only, to be placed in the driver folder preferably in c:\skipper\ESN200\. If you do not have this folder use the other .zip file with drivers included
Older versions
ESN200 1.1.4.3 Software for ESN200 echosounder.zip
ESN200 SW 1.1.3.0 Software for ESN200 echosounder.zip
ESN200 Software for ESN200 Echosounder 1.0.7.zipContaining latest SW version for ESN200 Display (ESN200-SB) and Electronic unit (JB70E2) and manual, Unpack the .zip and use the SW-M0XXX.tar files, do not unpack these.
SW-M010-1.0.7.0 & SW-M008-1.0.7.0 Added LAN printer(vis service software or APP) and ML1120 printer. Improvements of Diagnostics and bottom detection algorithm
Added Transducer KMS5018 selection, added options for DPT Max range, added Multiplex mode for ch1 and ch2 for using 2 transducers with the same frequency, extended internal history to 24h
SW-M010-1.0.6.2 black box software with fixes for shallow water, bug fix of untis in DBS,DBT,DBK NMEA sentences
SW-M010-1.0.6.1 black box software with fixes for shallow water, Diagnostic page, power failure on relay, Draft, NMEA2 input, other small bugs
SW-M008-1.0.6.0 Display software with improvments in shallow water detection
SW-M008-1.0.5.0 Display software with a number of gui improvements particularly in the diagnostics pages, SNR value (bottom detection threshold) can now be adjusted from scope screen.
SW-M0010-1.0.5.0 black box software with a number of improvements in bottom detection , and fix for jumping depth to zero, new settings levels.
SW-M008-1.0.4.0 Display software with a number of gui improvements and diagnostics improvements, improvement of TVG
SW-M010-1.0.4.0 Electronic unit software with improvements in filter, depth detction, range, TVG and noise rejection
Update using via LAN cable and Service software, ensure your PC is set up for static IP address in the same range as the unit (172.16.1.XXX)
Last updated 04.03.2020
SW for ESN200 1.1.0 w BAM changes.zipContaining latest SW version for ESN200 Display (ESN200-SB) and Electronic unit (JB70E2) and manual, Unpack the .zip and use the SW-M0XXX.tar files, do not unpack these.
SW-M010-1.1.0.0 & SW-M008-1.1.0.0 Complient with IEC62923 BAM standard, and IEC61162-450. Many changes - check the manuals
New text printer added Epson TM-T20III
SW-M010-1.0.7.0 & SW-M008-1.0.7.0 Added LAN printer(vis service software or APP) and ML1120 printer. Improvements of Diagnostics and bottom detection algorithm
Added Transducer KMS5018 selection, added options for DPT Max range, added Multiplex mode for ch1 and ch2 for using 2 transducers with the same frequency, extended internal history to 24h
SW-M010-1.0.6.2 black box software with fixes for shallow water, bug fix of untis in DBS,DBT,DBK NMEA sentences
SW-M010-1.0.6.1 black box software with fixes for shallow water, Diagnostic page, power failure on relay, Draft, NMEA2 input, other small bugs
SW-M008-1.0.6.0 Display software with improvments in shallow water detection
SW-M008-1.0.5.0 Display software with a number of gui improvements particularly in the diagnostics pages, SNR value (bottom detection threshold) can now be adjusted from scope screen.
SW-M0010-1.0.5.0 black box software with a number of improvements in bottom detection , and fix for jumping depth to zero, new settings levels.
SW-M008-1.0.4.0 Display software with a number of gui improvements and diagnostics improvements, improvement of TVG
SW-M010-1.0.4.0 Electronic unit software with improvements in filter, depth detction, range, TVG and noise rejection
Update using via LAN cable and Service software, ensure your PC is set up for static IP address in the same range as the unit (172.16.1.XXX)
Last updated 30.08.2021
SW-M008-1.1.4.5 Software for ESN200.zipContaining latest SW version for ESN200 Display (ESN200-SB) and Electronic unit (JB70E2) and manual, Unpack the .ZIP and use the SW-M0XXX.tar files, do not unpack these.
SW-M008-1.1.4.5 & SW-M010-1.1.4.5, Fixes in BAM, beeping, HBT and s:/d: order, bug fixes in GPS NMEA inputs
Also including
1.1.4.4 Fixes in UTC and local clock, Logging of raw data, small bugs
1.1.4.3 Fixes in GPS local time, Line printer formats, Logging to USB and internal logging.
1.1.4.2 Bugfix transducer runtime screen for second channel showed first channel again (since 1.1.4.0)
1.1.4.1 Bugfix Display had problems showing clock for NMEA port with ZDA sentence (since 1.1.3.0)
SW-M010-1.1.4.0 & SW-M008-1.1.4.0,
- ETS50200 transducer is limited to 70% on 200kHz and 60% on 50kHz. ETN50 ETN200S Are limited to 70%, ETS050 is limited to 60%, ETS200 is limited to 70%.
- Various bugfixes.
Last Updated 28.10.2022
ESN200 1.1.5.0 - Software for ESN200 echosounder.zipContaining latest SW version for ESN200 Display (ESN200-SB) and Electronic unit (JB70E2) and manual, Unpack the .ZIP and use the SW-M0XXX.tar files, do not unpack these.
SW-M008-1.1.5.0 & SW-M010-1.1.5.0, based on version 1.1.4.7 withthe following major changes.
Fix of UTC/Loc time
addition of PSKPDPT1 and 2 to allow PSKPDPT sentences to be sent separately on each NMEA, allowing use of IR301 and other older repeaters.
PSKPDPT now has a quality parameter
BAM & ALF improvements
improvements of LWE -450 messages
Memory and slowdown bug fixes
New manual

Last Updated 11.4.2025 - a patch to allow downgrade from later versions
ESN200 SW 1.1.2.0 - Software for ESN200 echosounder.rarContaining latest SW version for ESN200 Display (ESN200-SB) and Electronic unit (JB70E2) and manual, Unpack the .RAR and use the SW-M0XXX.tar files, do not unpack these.
SW-M010-1.1.2.0 & SW-M008-1.1.2.0, fixed issues with ALR, New EPV remote control features, Fixes on Printer parameters, New Synch - ready to ping, - New Manual
SW-M010-1.1.0.0 & SW-M008-1.1.0.0 Complient with IEC62923 BAM standard, and IEC61162-450. Many changes - check the manuals
New text printer added Epson TM-T20III
SW-M010-1.0.7.0 & SW-M008-1.0.7.0 Added LAN printer(vis service software or APP) and ML1120 printer. Improvements of Diagnostics and bottom detection algorithm
Added Transducer KMS5018 selection, added options for DPT Max range, added Multiplex mode for ch1 and ch2 for using 2 transducers with the same frequency, extended internal history to 24h
SW-M010-1.0.6.2 black box software with fixes for shallow water, bug fix of untis in DBS,DBT,DBK NMEA sentences
SW-M010-1.0.6.1 black box software with fixes for shallow water, Diagnostic page, power failure on relay, Draft, NMEA2 input, other small bugs
SW-M008-1.0.6.0 Display software with improvments in shallow water detection
SW-M008-1.0.5.0 Display software with a number of gui improvements particularly in the diagnostics pages, SNR value (bottom detection threshold) can now be adjusted from scope screen.
SW-M0010-1.0.5.0 black box software with a number of improvements in bottom detection , and fix for jumping depth to zero, new settings levels.
SW-M008-1.0.4.0 Display software with a number of gui improvements and diagnostics improvements, improvement of TVG
SW-M010-1.0.4.0 Electronic unit software with improvements in filter, depth detction, range, TVG and noise rejection
Update using via LAN cable and Service software, ensure your PC is set up for static IP address in the same range as the unit (172.16.1.XXX)
Last updated 30.08.2021
OS patch
SW M010-1.2.MB-M008-USB patch.tarThis software can be run one time to make the USB port on the JB70E2-SA run with USB-1.1 enabling all USB sticks to work. Hardware with SN over 40000 or supplied with SW-M008-1.2.0.0 (from June 25) or above will not require this
ESN200 1.2.0.1 - Software for ESN200 echosounder
ESN200 1.2.0.1- Software for ESN200 echosounder
ESN200 1.2.0.2 - Software for ESN200 echosounder
SW M008-1.2.0.2 Software for ESN200Display.tar
SW M010-1.2.0.2 Software for JB70E2-SA.tar
SW M019-1.2.0.2 Software for ESN200 Display M101 (6).tar